Hallo Gemeinde,
hier steht ein SLES 9 SP3 mit externem LTO-Roboter (Backup-Server). Dieser macht in letzter Zeit Probleme. Urplötzlich ist die Kiste im Netz nicht mehr erreichbar, die lokale Konsole zeigt nichts mehr an/ ist tot. es hilft nur noch ausschalten.
Anbei habe ich die Kernel-Meldungen (dmseg) beigefügt, in der Hoffnung ihr könnt mir sagen wo dem Rechenkünstler der sprichwörtliche Schuh drückt. Ich vermute irgendeine Art von SCSI-Problem.
…
ReiserFS: dm-7: checking transaction log (dm-7)
reiserfs: disabling flush barriers on dm-7
ReiserFS: dm-7: Using r5 hash to sort names
subfs 0.9
JBD: barrier-based sync failed on dm-2 - disabling barriers
JBD: barrier-based sync failed on dm-1 - disabling barriers
usbcore: registered new driver usbfs
usbcore: registered new driver hub
tg3.c:v3.37 (August 25, 2005)
ACPI: PCI interrupt 0000:03:01.0[A] -> GSI 48 (level, low) -> IRQ 19
eth0: Tigon3 [partno(BCM95703A30) rev 1002 PHY(5703)] (PCI:66MHz:64-bit) 10/100/1000BaseT Ethernet 00:0c:76:27:48:2f
eth0: RXcsums[1] LinkChgREG[0] MIirq[0] ASF[0] Split[0] WireSpeed[1] TSOcap[1]
eth0: dma_rwctrl[763f0000]
ACPI: PCI interrupt 0000:00:1f.5[B] -> GSI 17 (level, low) -> IRQ 17
PCI: Setting latency timer of device 0000:00:1f.5 to 64
NET: Registered protocol family 10
IPv6 over IPv4 tunneling driver
ACPI: Power Button (FF) [PWRF]
ACPI: Processor [CPU0] (supports C1)
ACPI: Processor [CPU1] (supports C1)
ACPI: Processor [CPU2] (supports C1)
ACPI: Processor [CPU3] (supports C1)
intel8x0_measure_ac97_clock: measured 50165 usecs
intel8x0: clocking to 48000
powernow: This module only works with AMD K7 CPUs
tg3: eth0: Link is up at 1000 Mbps, full duplex.
tg3: eth0: Flow control is on for TX and on for RX.
Linux agpgart interface v0.100 © Dave Jones
agpgart: Detected an Intel E7505 Chipset.
agpgart: Maximum main memory to use for agp memory: 941M
agpgart: AGP aperture is 16M @ 0xf9000000
tpm: module not supported by Novell, setting U taint flag.
tpm_atmel: module not supported by Novell, setting U taint flag.
USB Universal Host Controller Interface driver v2.2
ACPI: PCI interrupt 0000:00:1d.0[A] -> GSI 16 (level, low) -> IRQ 16
uhci_hcd 0000:00:1d.0: UHCI Host Controller
hw_random: RNG not detected
PCI: Setting latency timer of device 0000:00:1d.0 to 64
uhci_hcd 0000:00:1d.0: irq 16, io base 0000b400
uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 1
usb usb1: Product: UHCI Host Controller
usb usb1: Manufacturer: Linux 2.6.5-7.244-smp uhci_hcd
usb usb1: SerialNumber: 0000:00:1d.0
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 2 ports detected
ACPI: PCI interrupt 0000:00:1d.1[B] -> GSI 19 (level, low) -> IRQ 17
uhci_hcd 0000:00:1d.1: UHCI Host Controller
PCI: Setting latency timer of device 0000:00:1d.1 to 64
uhci_hcd 0000:00:1d.1: irq 17, io base 0000b000
uhci_hcd 0000:00:1d.1: new USB bus registered, assigned bus number 2
usb usb2: Product: UHCI Host Controller
usb usb2: Manufacturer: Linux 2.6.5-7.244-smp uhci_hcd
usb usb2: SerialNumber: 0000:00:1d.1
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 2 ports detected
ACPI: PCI interrupt 0000:00:1d.7[D] -> GSI 23 (level, low) -> IRQ 18
ehci_hcd 0000:00:1d.7: EHCI Host Controller
PCI: Setting latency timer of device 0000:00:1d.7 to 64
ehci_hcd 0000:00:1d.7: irq 18, pci mem f9990000
ehci_hcd 0000:00:1d.7: new USB bus registered, assigned bus number 3
PCI: cache line size of 128 is not supported by device 0000:00:1d.7
ehci_hcd 0000:00:1d.7: USB 2.0 enabled, EHCI 1.00, driver 2003-Dec-29
usb usb3: Product: EHCI Host Controller
usb usb3: Manufacturer: Linux 2.6.5-7.244-smp ehci_hcd
usb usb3: SerialNumber: 0000:00:1d.7
hub 3-0:1.0: USB hub found
hub 3-0:1.0: 4 ports detected
Non-volatile memory driver v1.2
end_request: I/O error, dev fd0, sector 0
end_request: I/O error, dev fd0, sector 0
hdc: ATAPI 48X DVD-ROM drive, 256kB Cache
Uniform CD-ROM driver Revision: 3.20
st: Version 20040318, fixed bufsize 32768, s/g segs 256
Attached scsi tape st0 at scsi0, channel 0, id 4, lun 0
st0: try direct i/o: yes (alignment 512 B), max page reachable by HBA 1048575
Attached scsi generic sg0 at scsi0, channel 0, id 4, lun 0, type 1
Attached scsi generic sg1 at scsi0, channel 0, id 6, lun 0, type 8
Attached scsi generic sg2 at scsi1, channel 0, id 0, lun 0, type 0
Attached scsi generic sg3 at scsi1, channel 0, id 1, lun 0, type 0
Attached scsi generic sg4 at scsi1, channel 0, id 2, lun 0, type 0
Attached scsi generic sg5 at scsi1, channel 0, id 15, lun 0, type 3
Attached scsi generic sg6 at scsi1, channel 1, id 8, lun 0, type 3
st0: Block limits 1 - 16777215 bytes.
BIOS EDD facility v0.16 2004-Jun-25, 3 devices found
eth0: no IPv6 routers present
mtrr: 0xfa000000,0x800000 overlaps existing 0xfa000000,0x400000
mtrr: 0xfa000000,0x800000 overlaps existing 0xfa000000,0x400000
scsi0:0:4:0: Attempting to queue an ABORT message
CDB: 0x12 0x1 0x0 0x0 0xfe 0x0
scsi0: At time of recovery, card was not paused
>>>>>>>>>>>>>>>>>> Dump Card State Begins >>>>>>>>>>>>>>>>>
(scsi0:A:4:0): Device is disconnected, re-queuing SCB
(scsi0:A:4:0): Abort Message Sent
Recovery code sleeping
(scsi0:A:4:0): SCB 3 - Abort Completed.
Recovery SCB completes
Recovery code awake
aic7xxx_abort returns 0x2002
Vielen Dank schonmal.
Eisbär